My 7" 3d Printed Alpha Tablet
anonymous 2019-03-26 21:47:51 16401 Views4 Replies I used this 3d printed file from thingiverse by sgtsmall.
https://www.thingiverse.com/thing:3317867
The side and large panel is not needed.
Capture+_2019-03-26-01-36-13-1.png (1.13 MiB) Viewed 15098 times
I had the modify the backplate with a dremel tool so that I could fit the battery in. I removed the piece of plastic around the red box.
Capture+_2019-03-26-00-38-47-1.png (1 MiB) Viewed 15098 times
Battery purchased from
https://s.click.aliexpress.com/e/cP0wTi6y
20190325_232214-1.jpg (1.35 MiB) Viewed 15098 times
I had to extend the 3 black wires so that I could bend the wires back just a little further, so I combined the 3 black wires together to a thicker wire (thats all I had at the moment). Then soldered it on the board where the 3 wires was soldered at.
20190325_210445-1.jpg (999.91 KiB) Viewed 15098 times
20190325_232737-1-1.jpg (140.72 KiB) Viewed 15098 times
20190325_232404-1.jpg (1.39 MiB) Viewed 15098 times
20190325_232558-1.jpg (1.22 MiB) Viewed 15098 times
I had to use a longer screw in the bottom right mount to support the corner of the backplate. It did not have any support before.
20190325_232855-1.jpg (1.45 MiB) Viewed 15098 times
I will add double sided adhesive or velcro to the battery and the backplate.
20190325_232645-1.jpg (660.88 KiB) Viewed 15098 times
20190325_232955-1.jpg (982.94 KiB) Viewed 15098 times
20190325_233036-1.jpg (1.15 MiB) Viewed 15098 times
20190325_233058-1.jpg (1.02 MiB) Viewed 15098 times
20190325_233216-1.jpg (670.59 KiB) Viewed 15098 times
20190325_233900-1.jpg (540.08 KiB) Viewed 15098 times
20190325_233637-1.jpg (580.12 KiB) Viewed 15098 times
20190325_233535-1.jpg (437.75 KiB) Viewed 15098 times
20190325_233557-1.jpg (602.7 KiB) Viewed 15098 times
I know its a little thick. I would like to slim it down sometime in the future once I upgrade to a bigger screen. I know its not perfect but it works for now.
https://www.thingiverse.com/thing:3317867
The side and large panel is not needed.
I had the modify the backplate with a dremel tool so that I could fit the battery in. I removed the piece of plastic around the red box.
Battery purchased from
https://s.click.aliexpress.com/e/cP0wTi6y
I had to extend the 3 black wires so that I could bend the wires back just a little further, so I combined the 3 black wires together to a thicker wire (thats all I had at the moment). Then soldered it on the board where the 3 wires was soldered at.
I had to use a longer screw in the bottom right mount to support the corner of the backplate. It did not have any support before.
I will add double sided adhesive or velcro to the battery and the backplate.
I know its a little thick. I would like to slim it down sometime in the future once I upgrade to a bigger screen. I know its not perfect but it works for now.
